Видео

Thanks! This was my grandpas car model. He passed about a year ago and so now it's my car, but the battery is dead. I got it out in under a minute!

Thanks! 👍

It's ok tearing it on the way out! It the way in that counts! :) The freezer trick is neat idea!

Thanks for the video. Just yanked mine out waiting for the aftermarket (Cardone/New from Rockauto). Hoping it works!

Thank you so much for the guidance! First time doing this on Pilot and you were spot on. Again thanks a lot

Oye como se llama esa pieza donde quitaste el tornillo

Thank you mr GM engineer for putting the battery in the trunk. You idiot !!

Heck ya! Thank you so much! I have been looking for a video on how to reset the radio. Everyone else's video talk about entering a code. You showed me that all I need to do is hold the power button! Amazing! And it worked on my 2014 pilot.

Whats the correct Mm to grt the hewd bolts off with .

I called out this company for their awful instructions and they are now looking to improve them with videos and more in depth written ones for customers

This is staged all that stuff was already loose that ain't the real world everybody knows you struggle to get the rotor off and all the other stuff it's not that easy

Wrong. Life oil is motor not transmission #2 car must be lebel to check transmission oil . MAN

It's worth taking it apart. There is a groove than runs the full length of the shaft that also goes around the shaft. This groove becomes clogged over time. Th purpose of the groove is to pull oil up on the shaft for lubrication. It can be cleaned using a dental pick and solvent. This process shown here will help a little but will not clean out the groove.

thanks about to do mine on my 89 f 250. somehow looks easier than the rear.

I tried one of these fittings but the grease just squirts out around the tip . None goes in the fitting

Very nice video, going to try to change mine tmw, do Have to pull the plug on your Inertia switch, to reduce pressure in the line. I have a no start 87 f150 I hear both pumps priming from each gas tank. I Half power to the inertia switch, That's telling me that my fuel pump relay, it's good. I replaced the fuel regulator it started stalled, started stalled now just cranks. Last time the fuel filter was changed. It was a little over 3 years ago. I'm not sure if this could be my issue, but thank you for posting such a great video

Ok so test #3 set at 200 reads 0.L set at 2k i get 0.L set at 20k 0.L set at 200k i get 24.2 is thatba pass or fail all other test checked out good

Thank you.....i was cursin like a drunkin sailor.

a "circular" blade have u ever seen a square one!!!!!!!!!

Only gas shocks comeback by themselves shocks without gas will stay where you put them

Do you still have old blue ?😊

Trump 2024

Enjoyed the video. Good, easy to watch, very helpful video!

Thanks this helps a lot I couldn't find mine apparently the previous owner removed it along with the rear tank which I am putting back on

Is there a little hole under your resevoir cap?

Ty! I'm a middle aged widow, it was late at night and I panicked. Was about to start crying! I found your video and did it myself and it worked!! Ty, so much and God Bless You!!! ❤❤❤

Lo mejor y explicativo qué he visto

Thanks I will try this and I never thought there was a hole to put grease there

awesome video very clear and good english

My 2003 does the same thing. Lift up on the wiper blade lever (as if you were trying to clean your windshield) then turn the key and crank the car. Then release the lever. Starts every time.

I recently changed my sensor in my hhr......as soon as i got the sensor off, some fluid poured out ....any thoughts?

My 77 400 has the dip stick on the driver's side? Why is yours on the passenger side?

Too much talking, not enough showing. I shouldn’t have to watch 7 minutes just to see how to do this

Nice job! Feel bad for you laying in that dirt. I would have to find a parking lot somewhere lol.

awesome job

good job

I used a Turkey bastor to suck out the old brake fluid.

I have a lot of customers who use the Haslet Frame that seals against water leaks and gives you a flat surface to install your fan.

This video saved me, I was about to lose my mind

They work O K

I've considered having mine done even though the manual says it isn't necessary with regular use. I only hesitate because of how doing a change can cause issues later if you go too long on the current fluid without changing it. Mine currently has just over 98,000 miles on it. How many miles were on the fluid in your HHR?

Thanks a million!!

Thank U for this HELPFUL tip, it worked for me in literally 2 seconds later my key was FINALLY OUT!!! It has been doing this for a while & it’s soooo helpful to know that I can finally have a solution without costing me hundreds of dollars that I don’t have right now!!! Thanks again 🤗 you’re a lifesaver!!!

thanks that is what i needed to know

You did it professionally

I laughed when you found the problem, but this was a great video for me, I appreciate seeing how it all comes apart before I do a camera install.

307k and still going bought our hhr new in 2007

Gracias excelente video

Hey great video, do u know what's the size for the bleeder valve in the rear?

What size battery does it really use. I believe the guy I purchased my car from changed the battery size